Datalux Recovery and Maintenance CD   V1.60
===========================================

The Recovery and Maintenance CD contains the files and utilities
necessary to recover a Datalux Tracer, IPIX or Databrick III unit.

Recovery and Maintenance operations available include the following:

   A. Create BIOS Upgrade Boot Floppy

   B. Create MS-Client Network Boot Floppy

   C. Re-install Windows on the Hard Drive        (Boot from this CD)

   D. Re-image the Hard Drive                     (Requires Image CD)

   E. Install utility programs


When booting from the CD-ROM, please note the following:

   -- The Teac CD-ROM drive must be plugged into the unit, not a hub.

   -- You will need a PS/2 keyboard when using the Teac CD-ROM in DOS.
      The Teac CD-ROM software will not install if any other USB devices
      are attached.


** THE DATALUX Recovery and Maintenance CD CONTAINS LICENSED SOFTWARE    **
**                                                                       **
** This is a companion disk to the Operating System disk you received    **
** with your unit and is bound by the same license terms.  Please refer  **
** to your Microsoft End User License Agreement (EULA) for details.      **
**                                                                       **
**              DO NOT MAKE ILLEGAL COPIES OF THIS DISK                  **



===============
A. BIOS Upgrade
===============

The "BIOS Upgrade" utility program will create a bootable floppy that will
automatically upgrade your BIOS.

NOTE:  BIOS Version 1.40 or higher is required to boot from a USB
       CD-ROM drive.

To create a BIOS upgrade floppy, please do the following:

1. Insert this CD into a system running Windows.

2. Double click on the "My Computer" icon and select the CD-ROM icon.

3. Double Click on the "FDD-BIOS Upgrade" icon.

4. Insert a blank floppy into drive "A:" when prompted.

5. Press Return to create a bootable floppy containing the new BIOS file.

6. Shutdown the Tracer, IPIX or Databrick III computer.

7. Insert the floppy in a USB Floppy Drive plugged into this unit.

8. Turn the unit on.

9. Press 'Y' to confirm upgrading the BIOS.

   DO NOT REMOVE POWER  - this may corrupt your BIOS and prevent the
   system from booting; if this occurs, the unit will have to be
   returned to the factory.

   The BIOS upgrade program will run and display a progress chart.

1O. When prompted, remove the Floppy and turn power to the unit off.



====================
B. MS-Client Network
====================

NOTE:  BIOS Version 1.50 or higher is required to boot and run MS-Client or
       most other DOS networks.

The "MS-Client Boot" utility program will create a bootable floppy that MAY
allow your unit to boot to your network.  Large variations in network
configurations may require additional files or settings not included herein.

A more generic boot disk that is Datalux Tracer / IPIX specific that seems
to work with many types of networks can be found here:

   \extras\MSCLIENT\MODBOOT

For other versions, get the latest image from here:

    http://www.nu2.nu


To create a MS-Client upgrade floppy, please do the following:

1. Insert this CD into a system running Windows.

2. Double click on the "My Computer" icon and select the CD-ROM icon.

3. Double Click on the "FDD MS-Client" icon.

4. Insert a blank floppy into drive "A:" when prompted.

5. Press Return to create a bootable floppy containing the MS-Client files.

6. Edit the "a:\net\system.ini" file for your user name, domain name and
   workgroup.  If you are using more than one boot disk on the same network
   you must also change the computer name to a unique name.

   Example:  username=MYNAME
             domainname=MYCOMPANY
             workgroup=MYGROUP
             computername=NAME001

   Contact your network administrator if you are unsure of your network
   settings.

7. Shutdown the Tracer, IPIX or Databrick III computer.

8. Insert the floppy in a USB Floppy Drive plugged into this unit.

9. Turn the unit on.

When the system boots, the network drivers and MS-Client drivers for
TCP/IP and DHCP will be loaded; a help message will be displayed.

   To get help on all network commands:      Q:\>net help
   To view your configuration:               Q:\>ipconfig
                                             Q:\>net config
   To login:                                 Q:\>net logon
   To view other computers on the network:   Q:\>net view

Again, there are a large number of variables that may prevent this disk
from working on your network.



==========================================
C. Re-install Windows on the Hard Drive
==========================================

** CAUTION: This procedure removes all existing data from your hard drive **
**          and installs only the Windows 98 Operating System.            **
**          Any programs or data on the drive will be erased.             **

Note: You will need a PS/2 keyboard when using the Teac CD-ROM in DOS.
      The Teac CD-ROM software will not install if any other USB devices
      are attached.

To completely re-install Windows:

1. Insert the Recovery and Maintenance CD into the CD-ROM drive.

2. Turn the unit on

3. Wait for the CD to boot and display the startup menu

4. Select menu option number 1.  This will perform the following operations:
   -- Reformat your hard drive
   -- Copy all Windows installation files to your hard drive
   -- Copy all Datalux drivers files to your hard drive
   -- Prompt you to remove the USB CD-ROM drive and reboot your computer.

5. When your computer boots again, it will start the Windows Setup program.
   For Best Results:
   -- Remove all USB devices until the installation is completed
   -- Accept all the defaults
   -- Reboot after loading each driver

6. Follow the instructions below to install these drivers:
   -- Audio Driver
   -- Video Driver
   -- Network Control Panel
   -- Touch Screen Driver (if your unit has a built-in touchscreen)


C.1 Install Windows 98 Audio Driver
===================================

To install the Audio Drive, please do the following:

1. Click on Start / Settings / Control Panel / System

2. Click on the Device Manager tab.

3. Click on "Other Devices" and expand this group.

4. Click once and highlight "PCI MULTIMEDIA AUDIO DEVICE".

5. Click Remove Button; Click OK on the "Confirm Device Removal" dialog.

6. Click Refresh.

7. The Add New Hardware Wizard will detect the Audio controller, Click Next.

8. Choose "Specify Location" and enter (or browse) to the following path:
   C:\DATALUX\DRIVERS\AUDIO\PW4046

9. Click Finish and the shutdown the computer with Start/Shutdown.


C.2 Install Windows 2000 Audio Driver
===================================

To install the Audio Drive, please do the following:

1. Click on Start / Settings / Control Panel / System

2. Click on the Hardware Tab and the "Device Manager" Button

3. Click on "Other Devices" and expand this group.

4. Click once and highlight "Multimedia Audio Controller".

5. Click Action / Properties for the Multimedia Audio Properties Dialog box

6. Click "Reinstall Driver" button

7. The Update Device Driver Wizard starts, Click Next.

8. Choose "Search for a suitable driver" and Click Next

9. Click Specify a location, Click Next

10. Click Browse and choose the following path:
   C:\DATALUX\DRIVERS\SOUND\W98SE-2K

11. Click Open and Click OK, the Update Device Driver Wizard will show "The wizard found..."

12. Click Next, click "Yes" to install without a signature

13. Click Finish, "Crystal WDM Audio Codec Properties" should be shown as "working properly"

14. Click Close and verify the Sound,video and game controllers contain the new driver.


C.3 Install Windows 98 Video Driver
===================================

Installation instructions are provided in

   \EXTRAS\Video_driver_install.pdf.

To view this file, install the Adobe Acrobat Reader program from:
   \EXTRAS\ADOBE\rp505enu.exe

(or go to http://www.adobe.com for the latest version)


To install the Video Driver, please do the following:

1. Click Start / Run / Browse for the following program:

   C:\DATALUX\DRIVERS\VIDEO\LYNX_CP\DISK1\SETUP.EXE

2. Click Open then OK to start the setup program.

3. Click Next and Next again, then Finish as prompted.

4. Click on Start / Shutdown / Restart / OK to restart the computer

5. Wait for the system to reboot to the Windows desktop.

6. Click on Start / Settings / Control Panel / System

7. Click on the Device Manager tab.

8. Click on "Display Adapters" and expand this group.

9. Click once and highlight "STANDARD PCI GRAPHICS ADAPTER"

10.Click Remove Button; Click OK on the "Confirm Device Removal" dialog.

11.Click Yes to Restart the computer.
   (If the system hangs and does not shutdown, press and hold the power
    button. You may have to restart from step #6)

12.At the next power up, the Graphics Adapter is detected. Select
   "Display a List..."

13.Click on "Have Disk" and direct Windows 98 to the following path:

   C:\DATALUX\DRIVERS\VIDEO\LYNX_DR

14.From Select Device dialog, Select Silicon Motion LynxEM+ and Click OK

15.An "Update Driver Warning" is displayed.  Just click Yes

16.Click Yes to install the driver

17.Click Finish and Yes to restart the computer yet again.


C.4 Install Windows 2000 Video Driver
===================================

To install the Video Driver, please do the following:

1. Click on Start / Settings / Control Panel / System

2. Click on the Hardware Tab and the "Device Manager" Button

3. Click on "Other Devices" and expand this group.

4. Click once and highlight "Video Controller (VGA Compatible)".

5. Click Action / Properties for the "Video Controller" Dialog box

6. Click "Reinstall Driver" button

7. The Update Device Driver Wizard starts, Click Next.

8. Choose "Search for a suitable driver" and Click Next

9. Click Specify a location, Click Next

10. Click Browse and choose the following path:
   C:\DATALUX\DRIVERS\VIDEO

11. Click Open and Click OK the Update Device Driver Wizard will show "The wizard found..."

12. Click Next, click "Yes" to install without a signature

13. The screen may blank a few times..Click Finish

Click Finish, "Silicon Motion LynxEM+ Properties" should be shown as "working properly"

14. Click Close and verify the Display Adapters contains the new driver.

15. From the desktop, right click on Properties / Settings - you can now change the resolution to match your screen.


C.5 Install Network Control Panel
=================================

The Network control panel provides utilities for network support and
diagnostics.

1. Click Start / Run and Browse to the following program:
   C:\DATALUX\DRIVERS\ETHERNET\intel_32\setup.exe

2. Click OK and start the Setup program.

3. Click Install then Click Done

4. Click Finish to close the setup program.

A network card Icon is displayed in the bottom right side of the desktop.
Double Click on this icon to start the utility.


C.6 Install Touch Driver
========================

Full documentation to install the touch driver can be found here:

   \EXTRAS\W2KME9x.pdf

To install the touch screen driver, run the setup program found here:

   \DATALUX\DRIVERS\MT_TOUCH\DISK1\setup.exe

You should re-calibrate the screen after the driver is installed.

To install the Touch Driver, please do the following:

1. Click Start / Run / Browse to execute the following program:
   C:\DATALUX\DRIVERS\MT_TOUCH\DISK1\SETUP.EXE

2. Click OK.

3. At the "Welcome" screen, click "Next".

4. At the "License" screen, click "Yes".

5. At the "Please Choose Controller..." screen, select "Serial", click "Next".

6. At the "Default Calibration Type" screen, select "5 Point", click "Next".

7. At the "Select Installation Type" screen, select "Express",  click "Next".

8. At the "Readme File" screen, click "No".

9. At the "Setup Complete" screen, select "Yes, I want to restart..."

10. Click "Finish".


C.7 Calibrate Resistive Touch Screens
=====================================

Note: For best results, use a plastic tipped pointer - ink pins, pencils or
      markers should not be used and may damage your screen.

If you have a resistive touch screen:

1. Click on the Start / Settings / Control Panel / Microtouch Touchware

2. Click on the Tools tab and then the Options Button

3. Click the Advance button.  From the Advanced Touchscreen Settings
   make sure the following are enabled (checked):
   -- 5 Point Calibration
   -- Enable Linearization
   -- Disable Calibration Reminder

4. Click Close on the Advanced Touch Screen Settings and Close on the
   Options dialog boxes.

5. While still in the Tools Tab, Click on the Linearization button,
   and Yes to do a 25 point linearization
   -- Carefully touch and HOLD the indicated points on the touch screen.
   -- Release each point when prompted.

6. Click Continue to do a 16 point calibration verification.
   -- Carefully touch and HOLD the indicated points on the touch screen.
   -- If the error value is larger than 1.5% redo the linearization.

7. Click on Tools/ Draw to verify the linearization.  For example:
   -- Press and hold on the upper left of the screen (as close to the border
      as you can get.
   -- Drag your finger across the top of the screen, down the right side,
      across the button and back up to the upper left corner.
   -- The lines you drew should be approximately straight.  If they have a
      large curve or angle, then redo the linearization.

8. Double Click to close the Draw screen.

9. Select the Calibrate tab and the big Calibrate button.

10.Do the calibration procedure as prompted

11.Click on OK to close the touch screen utilities program.



C.8 Calibrate Capacitive Touch Screens
======================================

If you have a capacitive touch screen:

1. Click on the Start / Settings / Control Panel / Microtouch Touchware

2. Click on the Tools tab and then the Options Button

3. Click the Advance button.  From the Advanced Touchscreen Settings
   make sure the following are enabled (checked):
   -- Enable Noise Filter (VERY IMPORTANT!!)
   -- 5 Point Calibration
   -- Enable Linearization
   -- Disable Calibration Reminder

4. Click Close on the Advanced Touch Screen Settings and Close on the
   Options dialog boxes.

5. Click on Cursor tab and select "Stabilize Cursor"
   -- this may take 3-4 minutes
   -- When done, choose the "Recommended frequency" selection
      (use cursor keys if necessary)

6. Click Apply, OK

7. While still in the Tools Tab, Click on the Linearization button,
   and Yes to do a 25 point linearization
   -- Carefully touch and HOLD the indicated points on the touch screen.
   -- Release each point when prompted.

8. Click Continue to do a 16 point calibration verification.
   -- Carefully touch and HOLD the indicated points on the touch screen.
   -- If the error value is larger than 1.5% redo the linearization.

9. Click on Tools/ Draw to verify the linearization.  For example:
   -- Press and hold on the upper left of the screen (as close to the border
      as you can get.
   -- Drag your finger across the top of the screen, down the right side,
      across the button and back up to the upper left corner.
   -- The lines you drew should be approximately straight.  If they have a
      large curve or angle, then redo the linearization.

10.Double Click to close the Draw screen.

11.Select the Calibrate tab and the big Calibrate button.

12.Do the calibration procedure as prompted

13.Click on OK to close the touch screen utilities program.


===================================
D. Image or Re-image the Hard Drive
===================================

** THE DATALUX IMAGE CD CONTAINS LICENSED SOFTWARE AND MUST BE PURCHASED  **
** FROM DATALUX.
**              DO NOT MAKE ILLEGAL COPIES OF THIS DISK                   **

** CAUTION: This procedure removes all existing data from your hard drive **
**          and installs only the Windows Operating System.               **
**          Any programs or data on the drive will be erased.             **

NOTE: This procedure requires using a PS/2 keyboard.  A USB keyboard
      will stop working after the CD-ROM drivers are loaded.

To completely re-image your hard drive:

1. Insert the Recovery and Maintenance CD into the CD-ROM drive.

2. Turn the unit on

3. Wait for the CD Boot to display the startup menu

4. Select menu option number 2

5. Insert the Image CD into the CD-ROM drive when prompted.
   This will perform the following operations:
   -- Install the CD-ROM drivers
   -- Prompt you to verify erasing the drive.
   -- Execute the Ghost program to restore the image.

You must have a Datalux Image CD or your own image CD created as described
below.


D.1. Create your own Bootable CD-ROM
====================================

To create a Bootable CD-ROM for your own image, this CD contains tools
and utilities that may help.  First, run the following:

1. Insert this CD into a system running Windows.

2. Double click on the "My Computer" icon and select the CD-ROM icon.

3. Double Click on the "Image CD-ROM Boot" icon

4. Insert a blank floppy into drive "A:" when prompted.

5. Press Return to create a bootable floppy containing the files required
   to boot the CD-ROM.


D.2. Create an Image CD-ROM
===========================

On the non-boot sector of the CD-ROM include these three items:

   1. The image file (the one you created or the Datalux Factory Image found:
      \DATALUX\UTILS\GHOST\W98_Vxxx.GHO

   2. The program to restore the image file
      (Norton Ghost is required for the Datalux Factory Image)

   3. An autoexec.bat file that executes this program to restore the
      image.
      A sample autoexec.bat file for the Datalux Image CD is on this CD at:
      \GHOST\

To burn a Bootable CD-ROM, tell your CD-ROM programming software to use
the Floppy created above and at least these three files listed.

NOTE: A demo program from "Ahead Software" is included on this CD-ROM at:

      \EXTRAS\NERO\

      This is a time limited demo program that will run until a specific date.
      Please download the latest version and purchase if you find this useful.
      This can be found at:

      http://www.nero.com



==============================
E. CD-ROM files for Windows 
==============================

The CD-ROMs contains some combination of the following files:

\autoexec.bat                   - example Image CD autoexec.bat
\ghostpe.exe                    - ** Norton Ghost 
\FDD-BIOS Upgrade               - Icon for creating a BIOS upgrade floppy
\FDD-Image CD-ROM Boot Track    - Icon for CD-ROM boot track for an Image CD
\FDD-Recovery CD-ROM Boot Track - Icon for CD-ROM boot track for a Recovery CD
\FDD-MS-Client Boot Disk        - Icon for creating MS-Client boot disk

\WIN98                          - *** Windows 98 CD-ROM Install files
\DATALUX\BIOS                   - latest BIOS version and programming utility
\DATALUX\DRIVERS                - factory image of all drivers
\DATALUX\WIN2k.PRO              - *** Windows 2000 CD-ROM install files
\DATALUX\UTILS                  - IE6.0, Power Point viewer and other programs 
\EXTRAS\ADOBE                   - Acrobat reader for viewing PDF files
\EXTRAS\MSCLIENT                - MS-CLIENT Networking with sample boot disks
\EXTRAS\NERO                    - demo program for burning CD-ROMS
\EXTRAS\OPERA                   - Open source Network browser
\EXTRAS\OPEN_OFF		- Open source Office suite
\EXTRAS\WIN_AMP                 - MP3 audio player
\EXTRAS\CD_TOOLS                - batch files for CD-ROM creation
\EXTRAS\CD_TOOLS\TOOLS\         - directory of useful tools for booting
\EXTRAS\CD_TOOLS\CMD_TOOLS\     - other command line tools

** The Norton Ghost program is only available on a Datalux Image CD which
   is purchased with a licensed copy of Norton Ghost.

*** Operating system CD-ROM files are copied here, depending on your OS.

========
Contacts
========

Contact Datalux Customer Support if you have any questions or need help
using this CD-ROM.


Contact via Internet:
http://www.datalux.com/support

Contact via Email:
support@datalux.com
uksupport@datalux.com


Contact via Phone:
Toll Free in the US: 1-888-811-0605
Jon Christian, Customer Support Representative, ext. 16
Matt Kave, Customer Support Manager, ext. 18
International: 540-723-4230, 31, 32, 33
Europe: 44 (0) 1293 540092

Contact via Fax:
USA and International: 540-723-4602
Europe: 44 (0) 1293-540094

Contact via Post:
Datalux Corporation
Customer Service Department
155 Aviation Dr.
Winchester, VA  22602

Datalux Europe
Customer Service Department
11 Pelham Court, Broadfield
Crawley, West Sussex RH11 9SH
United Kingdom


All trademarks are properties of their respective owners.

============
End of File.
============